1. Numbers are stored and transmitted inside a
computer in
(a)
binary form (b) ASCII code form (c) decimal form (d)
alphanumeric form
2. The original ASCII codes (a) were 7 bits (b) 8 bits (c) represented 256 characters (d)
represented 127 characters
3. The ASCII code of ‘A’ is (a) 66D (b) 41H
(c) 0100 0010 (d) 0110 0011
4. The ASCII code of ‘0’ (zero) is (a) 48D,
(b) 32H (c) 0011 1000 (d) 42H.
5. The 4-bit binary number
0111 represents (a) 15, (b) -7 (c) 7 (d) -1
- The decimal number 255 may be represented
by (a) 1111 1111B, (b) 1000 0000B, (c) EEEEH, (d) 0111 1111
- The 8-bit
binary number 1111 1111 represents (a) 255, (b) -255 (c) -127 (d) -1
6. The decimal number 127
may be represented by (a) 1111 1111B, (b) 1000 0000B, (c) EEH, (d) 0111 1111
7. A byte corresponds to (a)
4 bits (b) 8 bits (c) 16 bits (d) 32 bits
8. The storage required for
an image such as an X-ray is approximately (a) a few bytes (b) a few hundred
bytes (c) a few gigabytes (d) in the megabyte range.
9. A gigabyte represents (a)
1 billion bytes (b) 1000 kilobytes (c) 230 bytes (d) 1024 bytes
10. A megabyte represents
(a) 1 million bytes (b) 1000 kilobytes (c) 220 bytes (d) 1024 bytes
11. A Kb corresponds to (a)
1024 bits (b) 1000 bytes (c) 210 bytes (d) 210 bits
12. A superscalar processor
has (a) multiple functional units (b) a high clock speed (c) a large amount of RAM (d) many I/O ports
13. A 32-bit processor has
(a) 32 registers (b) 32 I/O devices (c) 32 Mb of RAM (d) a 32-bit bus or 32-bit
registers
14. Information is stored
and transmitted inside a computer in (a) binary form (b) ASCII code form (c) decimal form (d) alphanumeric form
15. The minimum number of bits required to store
the hexadecimal number FF is (a) 2, (b) 4, (c) 8, (d) 16
16. A parity bit is (a) used
to indicate uppercase letters (b) used to detect errors (c) is the first bit in
a byte (d) is the last bit in a byte
17. A 20-bit address bus allows access to a memory
of capacity (a) 1 Mb (b) 2 Mb (c) 32Mb (d) 64 Mb
18.
A 32-bit address
bus allows access to a memory of capacity (a) 64 Mb (b) 16 Mb (c) 1 Gb (d)
4 Gb
19. Clock speed is
measured in (a) bits per second (b) baud
(c) bytes (d) Hertz
20. On-chip cache has (a) lower access time than RAM (b) larger
capacity than off chip cache (c) its own data bus (d) become obsolete
21. An FPU (a) makes integer
arithmetic faster (b) makes pipelining more efficient (c) increases RAM
capacity (d) makes some arithmetic calculations faster
22. Pipelining improves CPU
performance due to
(a) reduced memory access
time (b) increased clock speed (c) the
introduction of parallellism (d) additional functional units
23. The system bus is made
up of (a) data bus (b) data bus and address bus (c) data bus and control bus
(d) data bus, control bus and address bus
24. The von Neumann
bottleneck is due to (a) mismatch in speed between secondary and primary
storage (b) mismatch in speed between the CPU and primary storage (c) slow
speed of I/O devices (d) low clock speeds
25. Cache memory enhances
(a) memory capacity (b) memory access time (c) secondary storage capacity (d)
secondary storage access time
26. Cache memory (a) has
greater capacity than RAM (b) is faster to access than CPU registers (c) is
permanent storage (d) faster to access than DRAM
27. A machine cycle refers
to (a) fetching an instruction (b) clock speed (c) fetching, decoding and
executing an instruction (d)executing an instruction
28. CISC machines (a) have
fewer instructions than RISC machines (b) use more RAM than RISC machines (c)
have medium clock speeds (d) use variable size instructions
29. RISC machines typically
(a) have high capacity on-chip cache memories (b) have fewer registers than
CISC machines (c) are less reliable than CISC machines (d) typically execute 1
instruction per clock cycle.
30. CPU performance may be
measured in (a) BPS (b) MIPS (c) MHz (d) VLSI
31. Modern processor chips
may be classified as (a) LSI (b) ULSI (c) MIPS (d) SSI
32. Silicon chips are
becoming more complex because (a) die size is decreasing (b) feature size is
decreasing (c) yield is increasing (d) the scale of integration is decreasing
33. Accessing disk storage
is slower than accessing RAM by an order of (a) 10 (b) 100 (c) 1000 (d) 100,000
34. The typical disk storage
capacity of a PC is of the order of (a) 32 MB (b) 2 Gb (c) 2 Tb (d) 5120 Kb
35. Disk access takes of the
order of (a) x millisecs (b) x microsecs (c) x/100 secs (d) x nanosecs
36. RAM access takes of the
order of (a) x millisecs (b) x microsecs (c) x/100 secs (d) x nanosecs
37. Cache memory access
takes of the order of (a) x millisecs (b) x microsecs (c) x secs (d) x nanosecs
38. Accessing RAM is slower
than accessing cache memory by an order of (a) 10 (b) 100 (c) 200 (d) 50
39. Optical tape storage (a)
has faster access time than disk storage (b) smaller capacity than CD-ROM (c)
greater capacity than DAT storage (d) smaller capacity than DAT storage
40. DIP involves the use of
a (a) scanner (b) plotter (c) microphone (d) CD-ROM
41. The typical RAM capacity
of a PC is of the order of (a) 32 MB (b) 16 Gb (c) 16 Tb (d) 512 Kb
42. Modem speeds are
measured in (a) bps (b) kbps (c) mbps (d) mips
43. LAN speeds are measured
in (a) bps (b) Kbps (c) Mbps (d) Mips
44. WAN speeds are (a)
usually higher than LAN speeds (b) measured in bytes per second (c) depend on
the transmission medium (d) limited by modem speeds
45. Accessing the Internet
from a typical home PC requires the use of (a) CD-ROM drive (b) a modem (c)
Windows 95 (d) Netscape
46. To use the Internet you
(a) must use the World Wide Web (b) must use electronic mail (c) use
appropriate communications software (d) must have a LAN account
47. A Pentium processor comprises (a) more than 1
million transistors (b) more than 3 million transistors (c) 500,000 transistors
(d) 900,000 transistors
48. Which of the following
is NOT a type of processor (a)
PowerPC 601 (b) Motorola 8086 (c) Motorola 68000 (d) Intel Pentium
49. Apple Macintoshs were
originally based on the (a) Intel 80x86 processor family (b) Motorola 68000
family (c) Motorola 6800 family (d) PowerPc family
50. IBM PC’s were originally
based on the (a) Intel 80x86 processor family (b) Motorola 68000 family (c)
Motorola 6800 family (d) PowerPc family
51. IBM used as the
operating system for their original PC (a) MS-DOS (b)Windows 3.1 (c) PC-DOS (d)
DOS
52. Windows (GUI) software
originated on (a) IBM computers (b) Apple Macintosh computers (c) Rank Xerox
computers (d) Digital (DEC) computers
53. A RAID system is useful
because (a) it increases processor speed (b) increases disk storage capacity
(c) increases disk storage capacity and availability (d) increases OS
efficiency
54. In processing cheques
which of the following I/O techniques have banks traditionally used (a)
OCR (b) MICR (c) barcode scanning (d) voice recognition
55 An RS-232 interface is
(a) a parallel interface (b) a serial interface (c) printer interface (d) a
modem interface
56. Which of the following
is NOT a computer performance metric: (a) MIPS,
(b) FLOPS, (c) SPECmark, (d) RISC
57. For print quality you would expect best
results from (a) line printer (b) dot matrix printer (c) ink-jet printer (d) laser printer.
58. Handling dates in the
next century is a serious problem for the computing industry. Which of the
following does NOT refer to this
problem: (a) Y2K problem (b) Year 2000 problem
(c) Millennium bug (d) Next century problem.
59. ROM (a) is faster to
access than RAM (b) is non-volatile (c) stores more information than RAM (d) is
used for cache memory
60. DRAM (a) is used for cache memory (b) is more
expensive than SRAM (c) is cheaper than SRAM (d) is only used at boot up time
61. SRAM (a) is cheaper than
DRAM (b) is used at boot up time only (c) is used for cache memory (d) is
slower to access than DRAM
62. 10-Base-T refers to (a)
Ethernet using thin coaxial cable (b) Ethernet using thick coaxial cable (c)
Ethernet using unshielded twisted pair (utp) cabling (d) none of the previous
63. 10-Base-2 refers to (a)
Ethernet using thin coaxial cable (b) Ethernet using thick coaxial cable (c)
Ethernet using unshielded twisted pair (utp) cabling (d) none of the previous
64. 10-Base-5 refers to (a)
Ethernet using thin coaxial cable (b) Ethernet using thick coaxial cable (c)
Ethernet using unshielded twisted pair (utp) cabling (d) none of the previous
65. The maximum recommended
segment length for utp is (a) 200 metres (b) 100 metres (c) 500 metres (d) 1000 metres
66. A UPS (a) increased the
storage capacity of a computer system (b) increases the process speed (c)
provides backup power in the event of a power cut (d) none of the previous
67. An NOS is (a) a proprietary operating system
(b) a network operating system (c) Novell Operating System (d) Unix-like
operating system
68. An NIC (a) a Novell
Interface Controller (b) used to control a printer (c) interfaces a modem to a
computer (d) connects a computer to a network
69. The capacity of a 3.5”
floppy is around (a) 100K (b) 1.4 Mb (c) 5 Mb (d) 1 Gb
70. The capacity of a 3.5” Zip disk is around (a)
5 Mb (b) 10 Mb (c) 40 Mb (d) 100 Mb
71. When accessing a disk
the amount of data transferred is (a) one track (b) one sector (block) (c) one
cylinder (d) 1 byte
72. A hard disk spins at x
revolutions per minute where x is (a) 300 - 900 (b) 30 - 90 (c) 3000 - 9000 (d)
100,000
73. The largest delay in
accessing data on disk is due to (a) seek time (b) rotation time (c) data
transfer time (d) none of the previous
74. CD-ROM capacity is
around (a) 100 Mb (b) 650 Mb (c) 1 Gb (d) 4 Gb
75. The capacity of a DVD is
around (a) 100 Mb (b) 650 Mb (c) 1.4 Gb (d) 4.7 Gb
76. The capacity of DAT is
(a) 100 Mb (b) 650 Mb (c) 1 Gb (d) several gigabytes
77. A smart card (a) is a
form of ATM card (b) has more storage capacity than an ATM card (c) is an
access card for a security system (d) contains a microprocessor
78. The resolution of a VGA
screen is (a) 1024 x 768 (b) 512 x 512 (c) 640 x 480 (d) 800 x 600
79. Laser printers usually
print at (a) 200 dpi (b) 360 dpi (c) 600
dpi (d) 10,000 dpi
80. High print quality
requires from (a) 600 dpi (b) 300 dpi (c) 1000 dpi (d)100,000 dpi
81. Laptop computers use (a)
CRT displays (b) LCD displays (c) SSGA displays (d) none of the previous
82. QWERTY is used with reference
to (a) screen layout (b) mouse button layout (c) keyboard layout (d) word
processing software
83. A “killer application”
is (a) software that is hard to debug ! (b) a form of computer virus (c) a
really popular application program (d) none of the previous
84. WYSIWYG is used with
reference to (a) screen layout (b) mouse button layout (c) keyboard layout (d)
screen images that resemble printed documents
85. A GUI is (a) hardware
(b) language interpreter (c) software interface (d) an operating system
86. Multiprogramming refers
to (a) having several programs in RAM at the same time (b) multitasking (c)
writing programs in multiple languages (d) none of the previous
87. Multitasking refers to
(a) having several programs in RAM at the same time (b) the ability to run 2 or
more programs concurrently (c) writing programs in multiple languages (d) none
of the previous
88. Multiprogramming is a
prerequisite for (a) multitasking (b) an operating system (c) to run more than
one program at the same time (d) none of the above
89. Timesharing is the same
as (a) multitasking (b) multiprogramming (c) multiuser (d) none of the previous
90. Virtual memory is (a)
related to virtual reality (b) a form of ROM (c) a form of RAM (d) none of the
previous
91. Multiprocessing is (a)
same as multitasking (b) same as
multiprogramming (c) multiuser (d) involves using more than one
processor at the same time
92. The most widely used
network operating system on PC LANs is (a) Linux (b) Novell Netware (c) Unix
(d) Windows NT
93. Disk fragmentation (a)
is caused by wear (b) caused by overuse (c) is due to bad disk blocks (d) none
of the previous
94. A compiler is (a) a fast
interpreter (b) slower than an interpreter (c) converts a program to machine
code (d) none of the previous
95. An interpreter is (a)
faster than a compiler (b) translates and executes programs statement by
statement (c) converts a program to machine code (d) none of the previous
96. JPEG and MPEG (a) have
to do with compression of graphics and video (b) have to do with Web pages (c)
the Internet (d) none of the previous
97. “Zipping” a file means
(a) encrypting it (b) decrypting it (c) compressing it (d) transmitting it
98. The speed of
transferring data with your modem is governed by (a) the speed of the your
modem (b) the speed of the receiving modem (c) the speed of
transmitting/receiving modems (d) the distance between the modems
99. ISDN speeds are (a)
faster than ATM speeds (b) slower than ATM speeds (c) same as modem speeds (d)
same as ADSL speeds
100. A cable modem uses (a)
LAN cable (b) cable-TV cable (c) is same speed as conventional modem (d) optic
fibre cables
101. A client-server system
is based on (a) mainframe technology (b) WAN technology (c) LAN technology (d)
Unix operating system
102. A multiplexor is a form
of (a) hub (b) modem (c) bridge (d) none of the previous
103. A hub is a (a) router
(b) a bridge (c) repeater (d) all of the previous
104. A search engine is (a)
hardware (b) IR system for the Internet (c) browser (d) none of the previous
105. An ISP (a) provides
access to the Internet (b) is a CPU register (c) is a CPU functional unit (d)
make of processor
106. FTP is (a) used to send
email (b) used to browse the Web (c) is part of Netscape (d) is a protocol for
the transfer of files between computers
107. Telnet (a) used to send
email (b) uses telephone lines (c) is part of Netscape (d) is a protocol that
allows for remote login
108. A firewall is (a) used
to protect a computer room from fires and floods (b) a form of virus (c) a
screen saver program (d) none of the previous
109. A proxy server is (a) a
backup server (b) an email server (c) a poor file server (d) none of the above
110. An RDBMS is a (a) remote DBMS (b) relative DBMS (c)
Relational DBMS (d) Reliable DBMS
111 Data Warehousing refers
to (a) storing data offline at a separate site (b) backing up data regularly
(c) is related to data mining (d) uses tape as opposed to disk
112. A 4GL is (a) DBMS
system (b) uses Java (c) uses C++ (d) none of the previous.
113. The Pentium processor
is (a) 16-bit (b) 32-bit (c) 64 bit (d) 8-bit
114. The IBM/Motorola
PowerPC 601 processor is (a) 16-bit (b) 32-bit (c) 64 bit (d) 8-bit
115. The Motorola 68000
processor is (a) 16-bit (b) 32-bit (c) 64 bit (d) 8-bit
116. The Digital Alpha
processor is (a) 16-bit (b) 32-bit (c) 64 bit (d) 8-bit
117. Apple’s iMac uses a (a)
ISA bus (b) NuBus (c) PCI bus (d) USB bus
118 Which of the following
is NOT a bus standard (a) EISA (b) VME (c) MCA (d) RS-232
119. A nanosecond is (a) 10-6 sec (b) 10-3 sec (c) 10-12 sec (d) 10-9 sec
120. The feature size of a
Pentium is approx. (a) 1 micron (b) 0.1 microns (c) 4 microns (d) .4 microns
121. The resolution of an
SVGA screen is (a) 1024 x 768 (b) 512 x 512 (c) 640 x 480 (d) 800 x 800
122. A 5 stage pipeline with the stages taking 1, 1, 3, 1, 1, units
of time has a throughput of (a) 1/3 (b) 1/7 (c) 7 (d) 3
123. Given a 5 stage pipeline with stages taking 1, 2, 3, 2, 1 units of
time, the throughput of the pipeline is:
(a) 9 (b) 1/9 (c) 1/3 (d) 2
124. Given a 5 stage pipeline with stages taking 1, 2, 3, 1, 1 units of
time, the clock period of the pipeline is:
(a) 8 (b) 1/8 (c) 1/3 (d) 3
125. Given a 5 stage pipeline with stages taking 1, 2, 3, 1, 1 units of
time, the flowthrough time of the pipeline is:
(a) 8 (b) 1/8 (c) 1/3 (d) 3
126. The average memory access time for a machine with a cache hit rate
of 90% where the cache access time is 10ns and the memory access time is 100ns
is (a) 55ns, (b) 45ns, (c) 90ns, (d) 19ns
127. The clock speed of a
modern PC is of the order of (a) 400 Khz (b) 400 Hz (c) 400 Mhz (c) 400 Ghz
128. Given that
the subprogram putc displays the character in al, the effect of
the following instructions:
mov
al, ‘c’
sub al, 2
call putc
is to (a) display 2 (b) display
'c' (c) display 'a' (d)
display a blank
129. Given that
the bl register contains ‘b’, the effect of the following
instruction
and
bl, 1101 1111
is to (a) clear bl (b) store ‘B’ in
bl (c) store 0010 0000 in bl (d) leave bl unchanged
130. Which of the
following is an illegal instruction
(a) MoV Ax,
30000
(b) iNc Al, 1 (c) aNd
bx, bx
(d) add ax, 30
131 An OR gate
generates a low output when (a) any one
of its inputs is low (b) all of its
inputs are high (c) when all of its
inputs are low (d) power fails
132. Given that the subprogram putc displays
the character in al, the effect of the following
instructions: mov
al, ‘a’
add al, 2
call putc
is to (a) display 2 (b) display c
(c) display a (d) display a blank
133. Given that the bl register
contains ‘B’, the effect of the following instruction
or bl, 0010 0000
is to (a) clear bl (b) store ‘b’ in bl (c) store 0010 0000 in bl (d) leave bl unchanged
or bl, 0010 0000
is to (a) clear bl (b) store ‘b’ in bl (c) store 0010 0000 in bl (d) leave bl unchanged
133b. Given that the bl register
contains ‘B’, which of the following instructions will change bl so that it
contains 'b' (a) or bl, 0010 0000 (b) and
bl, 0010 0000 (c) or bl, 1101 1111 in bl (d) and
bl, 1101 1111
133c. Given that the bl register
contains ‘b’, which of the following instructions will change bl so that it
contains 'B' (a) or bl, 0010 0000 (b) and
bl, 0010 0000 (c) or bl, 1101 1111 in bl (d) and
bl, 1101 1111
134. Which of the following is an illegal
instruction
(a) MoV Ax, 30000 (b) iNc
Al
(c) aNd bx, bx (d) add ax 30
135. An AND gate generates a high output when
(a) any one of its inputs is high (b)
all of its inputs are high (c) when all of its inputs are low (d) power fails
136. Given that
the subprogram putc displays the character in al, the effect of
the following instructions:
mov
al, ‘0’
add al, 2
call putc
is to (a) display ‘2’ (b) display '3' (c) display '0' (d) display a blank
add al, 2
call putc
is to (a) display ‘2’ (b) display '3' (c) display '0' (d) display a blank
137. Given that the bl register
contains 1111 0000, the effect of the following instruction
or
bl, 0000 1111
is to (a) clear bl (b) store 1111
1111 in bl (c) store
0000 1111 in bl (d) leave bl unchanged
138. Which of the
following is an illegal 8086 instruction
(a) mov 20,
bx
(b) iNc Al (c) aNd bx, bx (d) add
ax, 30
139. Which of the
following is an illegal l8086
instruction
(a) mov ax,
[bx] (b) iNc [bx] (c) aDd bx, [bx] (d) add
ax, [cx]
140. Which of the
following is an illegal 8086 instruction
(a) mov ax, [bx] (b) iNc [bx] (c) aDd bx, [dx] (d) add
[bx], 1
141. Which of the following is an illegal
8086 instruction
(a) ret 2 (b) push al (c) aDd
bx, 25000 (d) and ax, dx
142. The net effect of calling the following
subprogram in terms of program behaviour:
Subprog: push ax
add ax, 10
ret
is to (a) leave ax unchanged (b) add 10 to ax
(c) cause the program to behave in an unpredictable manner (d) do nothing
143. Branch prediction is used in the context
of (a) pipelining (b) program loops (c) cache memory (d) ALU operation
144. Delayed branching is used (a) to
introduce delays in program execution (b) in pipelining (c) in cache memory (d)
decoding instructions
145. A Harvard architecture means that a
machine has (a) separate memories for data and instructions (b) unified cache
memory (c) multiple functional units (d) an on-chip cache
146. Which is the most complex component of
the following (a) transistor (b) flip flop
(c) AND gate (d) decoder
147. An assembly language instruction (a)
always has a label (b) always takes at least 1 operand (c) always has an
operation field (c) always modifies the status register
148. An arithmetic instruction always
modifies the (a) stack pointer (b) status register (c) program counter (d) an
index register
149. A conditional jump instruction (a)
always cause a transfer of control (b) always involves the use of the status
register (c) always modifies the program counter (d) always involves testing
the Zero flag
150. An interrupt instruction (a) causes an
unconditional transfer of control (b) causes a conditional transfer of control
(c) modifies the status register (d) is an I/O instruction
151. A data movement instruction will (a)
modify the status register (b) modify the stack pointer (c) modify the program
counter (d) transfer data from one location to another
152. The memory address register is used to store
(a) data to be transferred to memory (b) data that has been transferred from
memory (c) the address of a memory location (d) an instruction that has been
transferred from memory.
153. The memory data register is used to
store (a) data to be transferred to or
from memory (b) data to be transferred to the stack (c) the address of a memory
location (d) an instruction that has been transferred from memory
154. The instruction register stores (a) an
instruction that has been decoded (b) an instruction that has been fetched from
memory (c) an instruction that has been executed (d) the address of the next
instruction to be executed
155. The program counter (a) stores the
address of the instruction that is currently being executed (b) stores the next
instruction to be executed (c) stores the address of the next instruction to be
executed (d) stores the instruction that is being currently executed.
156. The stack pointer stores (a) the address
of the stack in memory (b) address of the last item pushed on the stack (c) the
address of the next free stack location (d) the address of the last item popped
from the stack
157. The read/write line is (a) belongs to
the data bus (b) belongs to the control bus (c) belongs to the address bus (d)
CPU bus
158. The instruction inc I where I is a memory
variable involves (a) a memory read operation (b) a memory write operation (c)
a memory read and a memory write operation (c) only an arithmetic operation
159. Memory mapped I/O involves (a)
transferring information between memory locations (b) transferring information
between registers and memory (c) transferring information between the CPU and
I/O devices in the same way as between the CPU and memory (d) transferring
information between I/O devices and memory
160. Busy waiting is a technique (a) to allow
the CPU wait for a busy device (b) to allow a busy device wait for the CPU (c)
to keep an idle device busy (d) improve CPU performance
161. A hardware interrupt is (a) also called
an internal interrupt (b) also called an external interrupt (c) an I/O
interrupt (d) a clock interrupt
162. An assembly language program is
typically
(a) non-portable (b) shorter than an
equivalent HLL program (c) harder to read than a machine code program (d)
slower to execute than a compiled HLL program
163. Programs are written in assembly
language because they (a) run faster than HLL programs (b) are portable (c)
easier to write than machine code programs (d) they allow the programmer access
to registers or instructions that are not usually provided by a HLL
164. An assembly language program is
translated to machine code by (a) an assembler (b) a compiler (c) an
interpreter (d) a linker
165. An assembly language directive is (a)
the same as an instruction (b) used to define space for variables (c) used to
start a program (d) to give commands to an assembler
166. Which of the following is not an MASM
directive (a) .stack (b) db (c) .model (d) call
167. When a program is translated by the MASM
assembler, the machine code is stored in a file with the extension (a) .lis (b)
.obj (c) .exe (d) .out
167a. The output of the linker (LINK command)
is stored in a file with the extension (a) .lis (b) .obj (c) .exe (d) .lnk
168. Which of the following is not part of the processor
(a) the ALU (b) the CU (c) the registers (d)
the system bus
169. Which of the following variables uses
the most amount of RAM:
(a) x db 255
(b) y db 80 dup(‘Z’) (c) z dw 50 dup(0)
(d) small dd 40 dup(0)
170. Which of the following defines a
constant Max
(a) Max db 80
(b) Max equ 80 (c) Max dw 80
(d) mov Max, 80
171. The result of mov al,
65
is to store
(a) 0100 0010 in al, (b) ASCII code of ‘A’ in
al, (c) store 42H in al (d) store 1000 0001 in al
172. The call instruction is
used to (a) access subprograms (b) access memory (c) perform I/O (d) access the
stack
173. The effect of the following instructions
push ax
add ax, 4
pop bx
mov cx, ax
push bx
pop ax
on the ax register is (a) leave it with its original value (b) add 4 to it (c) clear it (d) double it
push ax
add ax, 4
pop bx
mov cx, ax
push bx
pop ax
on the ax register is (a) leave it with its original value (b) add 4 to it (c) clear it (d) double it
174. To copy the hexadecimal number A to the
bh register you write
(a) mov 0bh, ah (b) mov bh, 0ah (c) mov bh,
ah (d) mov bh, [ah]
175. The effect of the following instructions
mov ah, 2h
int 21h
is to (a) read a character into al (b) read a character into dl (c) display the character in al (d) display the character in dl
mov ah, 2h
int 21h
is to (a) read a character into al (b) read a character into dl (c) display the character in al (d) display the character in dl
176. The effect of the following instructions
mov ah, 1h
int 21h
is to (a) read a character into al (b) read a character into dl (c) display the
character in al (d) display the character in dl
177. Given that al contains the ASCII code of
an uppercase letter, it can be converted to lowercase by (a) add al, 32 (b) sub
al, 32 (c) or al, 1101 1111 (d) and al, 0010 0000
178. Given that al contains the ASCII code of
a lowercase letter, it can be converted to uppercase by (a) add al, 32 (b) sub
al, 32 (c) or al, 1101 1111 (d) and al, 0010 0000
179. Given that al contains the ASCII code of
an uppercase letter, it can be converted to lowercase by (a) add al, 30 (b) sub
al, 30 (c) or al, 0010 0000 (d) and al, 0010 0000
180. Given that al contains the ASCII code of
a lowercase letter, it can be converted to uppercase by (a) add al, 32 (b) sub
al, 30 (c) or al, 1101 1111 (d) and al, 1101 1111
181 The instruction jg operates with
(a) unsigned numbers (b) 2’s complement numbers (c) floating point numbers (d) ASCII codes
182 The instruction ja operates with
(a) unsigned numbers (b) signed numbers (c) floating point numbers (d) ASCII codes
183 The instruction mov
str[si], ‘a’ is an example of (a) indirect addressing (b) indexed addressing (c)
direct addressing (d) register addressing
184 The instruction mov ax,
[bx] is
an example of (a) indirect addressing (b) indexed addressing (c) direct
addressing (d) based addressing
185 The instruction je label is an example of
(a) indirect addressing (b) indexed addressing (c) relative addressing (d)
immediate addressing
186. The word size of an 8086 processor is
(a) 8 bits
(b) 16 bits (c) 32 bits (d) 64 bits
187. The code used to boot up a computer is
stored in (a) RAM (b) ROM (c) PROM and (d) EPROM
188. In accessing a disk block the longest
delay is due to (a) rotation time (b) seek time (c) transfer time (d) clock
speed
189. Given that putc displays a character,
the following code
mov
al, ‘a’
add
al, 2
and
al, 1101 1111
call
putc
is to (a) display 2 (b) display ‘c’ (c) display ‘C’ (d) display ‘A’
190. Given that bl contains ‘B’ the effect of
the following code
or
bl, 0010 0000
add
bl, 2
is to (a) clear bl, (b) store ‘b’ in bl (c)
store 0110 0001 in bl (d) store ‘d’ in
bl
191. The average memory access time for a
machine with a cache hit rate of 90% where the cache access time is 10ns and
the memory access time is 100ns is (a) 55ns, (b) 45ns, (c) 90ns, (d) 19ns
192. Which of the following
is NOT involved in a memory write operation: (a) MAR, (b) PC, (c)
MDR, (d) Data Bus
193. Pipelining improves CPU
performance due to
(a) reduced memory access
time (b) increased clock speed (c) the
introduction of parallellism (d) additional functional units
194. DRAM (a) is used for cache memory (b) is more
expensive than SRAM (c) is cheaper than SRAM (d) is only used at boot up time
195. SRAM (a) is cheaper
than DRAM (b) is used at boot up time only (c) is used for cache memory (d) is
slower to access than DRAM
196. WYSIWYG is used with
reference to (a) screen layout (b) mouse button layout (c) keyboard layout (d)
screen images that resemble printed documents
197. A GUI is (a) hardware
(b) language interpreter (c) software interface (d) an operating system
199. FTP is (a) used to send
email (b) used to browse the Web (c) is part of Netscape (d) is a protocol for
the transfer of files between computers
200. Telnet (a) used to send
email (b) uses telephone lines (c) is part of Netscape (d) is a protocol that
allows for remote login
201. Which of the following is an illegal
8086 instruction
(a) ret 2 (b) push ax (c) aDd
bx, 25000 (d) mov x, ay
202. The read/write line is (a) belongs to
the data bus (b) belongs to the control bus (c) belongs to the address bus (d)
CPU bus
203. The call instruction
stores the return address for a subprogram (a) on the stack (b) in the memory
address register (c) in the program counter (d) does not involve using the
return address
204 The instruction je label is an example of
(a) indirect addressing (b) indexed addressing (c) relative addressing (d)
immediate addressing
205. Given that dl contains 'x' which of the
following will cause 'x' to be displayed:
(a) mov ah, 1h (b) mov ah,
2h (c) mov ah, 2h (d) mov ah, 0h
int 21h int 20h int 21h int 21h
int 21h int 20h int 21h int 21h
206. Which of the following will read a
character into al:
(a) mov ah, 9h (b) mov ah,
2h (c) mov ah, 2h (d) mov ah, 1h
int 21h int 20h int 21h int 21h
int 21h int 20h int 21h int 21h
207. Which of the following will display a
string whose address is in the dx register:
(a) mov ah, 0h (b) mov ah,
2h (c) mov ah, 9h (d) mov ah, 9h
int 21h int 20h int 21h int 22h
int 21h int 20h int 21h int 22h
208. Which of the
following will terminate a program and return to MS-DOS:
(a) mov ax, 4c00h (b) mov
ax, 4c00h (c) mov dx, 4c00h (d) mov ax, 9h
int 20h int 21h int 21h int 22h
int 20h int 21h int 21h int 22h
209. The cmp instruction modifies the (a)
program counter (b) instruction register (c) flags register (d) segment
register
210. Conditional instructions typically
inspect the (a) program counter (b) instruction register (c) flags register (d)
accumulator
211.The bp register is typically used for
accessing (a) strings (b) memory (c) stack (d) data segment
212. The ret instruction modifies the (a)
instruction register (b) program counter (c) address register (d) flags
register
213. The sp register is typically used for
accessing (a) strings (b) memory (c) stack (d) data segment
214. The call instruction modifies (a) the
flags register (b) program counter (c) bp register (d) none of the previous
215. The call instruction modifies (a) the
flags register (b) stack pointer (c) bp register (d) none of the previous
216 The call instruction modifies (a) the
program counter and SP register (b) flags register (c) bp register (d) none of
the previous
217. The ret instruction modifies the (a)
stack pointer (b) bp register (c) instruction register (d) flags register
218. One type of main memory in a PC is
called (a) SRAM (b) SDRAM (c) ROM (d) DROM
